How To Use A Table Saw Safely: Helpful Tips For Carpenters

How To Use A Table Saw Safely

One of the problems that any carpenter is concerned with is how to use a table saw safely. Let’s learn and analyze the key steps with us via this article.

A table saw is the ultimate tool for any carpenter or home DIYer interested in wood projects. Its saw blade is powerful enough to make sharp and clean cuts on your board. Learn more best table saw under 500 dollars here

With such power, you need to take full caution when using table saws to avoid injuring yourself. To learn how to use a table saw safely, refer to these steps:

  • When the material is near the blade, do not start the table saw.
  • When performing rip cutting, always use a rip fence.
  • Always use a miter gauge for crosscuts.
  • During cutting, keep the material flat.
  • Protect your eyes and ears when working.

To understand more details about the steps, continue reading our shares below.

How To Use A Table Saw Safely

It is not rare for users to experience severe injuries due to improper use of table saws.

One of the most common issues is where the material gets caught in the blade, and the lanyard then kicks back, resulting in a hand injury. Please note the following safety provisions if you do not want to turn your carpentry experience into a disaster.

Checking the material carefully

How To Use A Table Saw Safely

Before learning how to use a table saw safely, keep yourself a serious attitude. You must understand that their blades are sharp enough to cut your fingers.

The first action you should take note of is the material inspection.

If you put the material too close to the blade, it will cause kickback when starting. This phenomenon is related to your workpiece when turning or twisting will lose alignment in the middle of the cut, causing it to no longer be parallel to the blade.

As a result, the teeth and blade cling to the wood and violently bounce back towards you.

Table saws often have very high cutting speeds so that you can predict the consequences.

In addition to checking the materials, you can also use the accompanying support tools such as anti-kickback pawls or riving knives. They are all available in the package when you buy them.

Using rip fence for rip cuts

How To Use A Table Saw Safely 1

Notice a long, thin block that runs parallel to the blade; it’s called the rip fence. This tool is essential for processes that require rip cuttings or vertical wood cutting.

Pressing the workpiece onto the rip fence will help shape the blade in a perfectly parallel direction. As a result, kickbacks will be less likely to happen.

Using miter gauge for crosscuts

How To Use A Table Saw Safely 2

Similar to rip cuts, you need additional equipment to make safe crosscuts. Remember that rip fences won’t be of much help in this situation because crosscuts involve horizontal cuts.

The miter gauge is the most accurate choice for you. This system will help your blade cut more compactly and firmly to avoid kickback problems.

One trick we recommend for weekend warriors who often have to make large crosscuts is adding wood blocks or building a sled to your miter gauge. It will expand the size you can measure to cut broader cuts.

If you want to add more traction to the cut, consider adding 120 or 220 grit sandpaper to the edge.

Keep the material flat during the cut

How To Use A Table Saw Safely 3

Avoid curved or bumpy boards when cutting. They interfere with machining and are not safe for you.

With rough surfaces, these boards cannot make complete contact with the rip fence or miter gauge. It leads to a feeling of entanglement when cutting and, worse, kickbacks or binds.

In case you don’t have a lot of ingredients or need to use that crooked board, follow these steps:

  • Cut a sheet of plywood about 6 inches wide.
  • Secure the crooked board to the freshly cut plywood with screws or finishing nails. One note is that you need to keep the pin away from the edge to avoid contact with the saw blade.
  • Bring the flat part of the plywood into complete contact with the rip fence and miter gauge. You can cut as usual after that.

Even if you’re cutting planks with a flat surface, avoid direct contact with the blade with your hands. We cannot predict the future at all.

A powerful support tool for you is the push stick. It makes it easy to hold the boards in place without getting your hands too close to the blade.

Protect your eyes and ears

How To Use A Table Saw Safely 4

Not only protect your hands, but you also have to pay attention to your eyes and ears when using a table saw.

During the operation and cutting of wood, the blade will produce quite a lot of wood chips. The wood chips will scatter in the air and make your eyes sting and blur. Things will get even worse if a large piece of woodlands shots in your eye.

Therefore, always wear goggles to cover your eyes to avoid bad situations.

The ear is also a sensitive part that you must protect. The motor of table saws is usually potent, so it produces a large volume when operating. Use earplugs or noise-canceling earmuffs to reduce noise entering your ears.

Final Words

No matter what you do, always remember that safety comes first. In the process of learning how to use a table saw safely, you will keep in mind the guides for a successful cutting experience.

We also recommend you carefully read the manual instructions to understand more about the use of each device. See more power tool here

Happy sawing!